One Engine Fire Can Shut Down Your Entire Operation.
Mulchers, stump grinders, and forestry machines ignite fast and burn from the inside out. BlazeCut automatically suppresses engine-bay fires before you lose the machine, the job, or the season.
Forestry Equipment Fires Are Not "What If?" - They're "When?"
Forestry machines run hot, operate under load, and pull dry debris into enclosed engine compartments.
That combination makes fire risk unavoidable. One overheated component or hydraulic failure is enough to ignite everything around it.
Most of these fires start inside the engine bay, out of sight. By the time smoke or heat is noticeable, the fire is already established and spreading.
Most equipment losses don’t happen because of mistakes. They happen during normal work on machines doing exactly what they were built to do.
The difference between a close call and a total loss is simple: whether suppression was already in place when the fire started.
Fires Happen Without Warning - BlazeCut Protects What You've Worked So Hard To Build Without Hesitation - Automatically, 24/7
1. Heat Is detected
BlazeCut senses dangerous temperature spikes inside your engine bay or electrical enclosure automatically.
2. Critical Temp Is Exceeded
At around 267°F, the pressurized tube melts precisely at the hottest point. The FK-5-1-12 agent floods the fire source instantly - no residue, no harm to your engine.
3. The Fire Is Stopped In Seconds
Before you can even react, before you even have a chance to pull to the side of the road - it’s over. Fire suppressed, car saved.
BlazeCut Protection For Forestry Operation
"I CANNOT STRESS TOo STRONGLY THAT THE BLAZECUT FIRE SUPPESSION SYSTEM ALONE SAVED MY CAR!! YOU CAN'T GET BETTER FIRE PROTECTION!"
- BlazeCut saved Mark's vintage Lotus Espirt moments after the engine bay erupted in black smoke and flames. The fire didn't even have time to singe the paint.
** Unit pictured is legacy model - new models have black heat sensing tube **
Forestry Equipment Is Always One Failure Away from Fire
Heat. Fuel. Hydraulics under pressure. Dry debris.
That is not an edge case in forestry. That is normal operation.
Most equipment fires don’t happen because of neglect.
They happen because one component fails under load and the fire grows faster than anyone can react.
BlazeCut is automatic fire suppression designed for that reality.
It activates when temperatures spike and suppresses fire at the source without power, sensors, or human input.
No reaction required.
No guesswork.
No dependence on perfect timing.
Just fire suppression that works in the conditions forestry equipment actually operates in.
Fully Automatic
No wires, no triggers, no worries — BlazeCut is always ready
Clean Suppression
Our FK-5-1-12 agent is safe for people, your engine, and the environment
Easy DIY Install
Installs in minutes - protects for years without any maintenance needed
Installs Simply. Protects Continuously.
BlazeCut installs directly into engine compartments and high-risk enclosures on forestry equipment without modifying a thing.
No wiring. No drilling. No system integration.
Each unit is fully self-contained and mounts in minutes using simple brackets or zip ties. It fits skidders, harvesters, forwarders, processors, and generators without interfering with operation or service access.
Once installed, it stays out of the way. Until it’s needed.
When heat spikes, BlazeCut activates automatically and suppresses fire at the source with a clean, residue-free agent that won’t damage engines, hydraulics, wiring, or electronics.
No mess. No cleanup. No downtime.
Just automatic fire suppression that works while the job keeps moving.
Forestry Fires Escalate Fast. BlazeCut Acts First.
Automatic fire suppression that works while the machine is running, after shutdown, or when no one is there to react.
Frequently asked questions
What If I need a bigger unit than what you have?
Just email me at brandon@modernfiresuppression.com and we can talk about bumping you up to our canister systems.
Can BlazeCut handle the heat and conditions of forestry work?
Yes. BlazeCut is designed for environments with sustained heat, vibration, debris, and continuous operation. It activates only at fire-level temperatures, not normal operating heat, making it suitable for forestry equipment that runs hot and works under load for long periods.
Can I install it myself?
Absolutely. Every unit can be installed without modifying your equipment in any permanent way - no wiring needed.
No. BlazeCut installs inside engine compartments or enclosures without modifying the machine or interfering with operation, airflow, or service access. It stays out of the way during normal use and does not affect performance, maintenance schedules, or routine inspections.
You can use our sizing assistant by clicking the chat bubble in the bottom right of your screen or in the main menu. Or you can calculate how much square footage you need protected and compare that to the tech specs on each product page. If worse comes to worse you can email us at: brandon@modernfiresuppression.com
What happens after BlazeCut activates?
When BlazeCut activates, it suppresses the fire at the source using a clean, residue-free agent. The system is discharged and must be replaced, but there is minimal cleanup and far less damage compared to uncontrolled fires or powder-based suppression systems.